74452.35USD
58.66USD
1.55USD
0.1USD
2178.0USD
9.41USD
738.52USD
93.64USD
0.1USD
0.03USD
0.1USD
Video Upload Q&A Likes Trends
@Ada
Check the ground resistance of LDO is normal or abnormal. If it is abnormal, consider replacing the LDO. If it is normal, test the input voltage of pin 5 to determine if it is sufficient for voltage conversion.
What should be done if the 1.8V and 0.8V voltages are abnormal?
@Ada
Check if the fixture is functioning properly or if a reboot is required. Verify the reliability and integrity of the fixture. Investigate any potential issues with the data cable interface. Abnormal resistances at the interface are often the cause. By performing these checks, you can identify and address any issues related to the fixture or data cable interface that may be causing the abnormal RST reset voltage.
The report shows a value of 0, while the RI voltage is normal. The reset voltage for the first chip (RST) is 0, while the other voltages are normal. What could be the possible explanation for this anomaly?
@Ada
In this case, you should short-circuit the CO signal of the chip and continue the process. If short the output CO signal of chip 1 ,reports asic 1, continue with the rest of the chips. Identify the defective chip that cannot receive the signal and replace it.
The voltage and resistance measurements appear normal, but the fixture still displays 61.
@Ada
See the kernel log. Temperature can not go up. Update the new firmware.
What could be the reason for the new S17+ machine failing to start up?
@Ada
Usually the hashboards have problem. Do single-board test.
Which aspects should be checked when the T17 miner experiences dropped boards?
@Ada
Replace the power management IC and check all the LDOs.
What does it mean when the L3+ miner displays this error code and continuously cycles through it?
@Ada
Machines that were previously running fine but cannot run after board stacking may not be related to frequency but rather to the BIN (firmware version) used. Try using similar BIN versions, such as BIN4, and check if the A5V1R (ASIC version) is the same.
Do we need to recalibrate the frequency for the T15 multi-board miner that is unable to start up?
@Ada
The PSU is abnormal. Replace and test again.
How to deal with a non-rotating power supply fan on the T17? After running for a few minutes, the back-end logs indicate a temperature control chip failure. Do I need to replace the power supply fan?
@Ada
Error_ASIC_LOSS,do the single board test to find out the defective chips.
What could be the problem with this T17+ miner?
@Ada
Check the voltage and systematically troubleshoot each component to identify and eliminate the issues one by one.
After repairing the T15, it initially detects and tests 60 chips successfully. However, it subsequently starts producing garbled output. How can I effectively diagnose and identify the source of this problem?
@Ada

Replace the power management IC [U1]

The S9's cross-domain voltage is only 0.28V and the 8.5V voltage is missing. Despite troubleshooting the PIC and MOS tubes, the issue persists. What could be the cause of this problem?
@Ada
Please check the complete kernel log.
After repairing the S9K and successfully passing the fixture test, it still lacks computational power when running both with multiple boards and individual boards. What could be the underlying issue causing this problem?
PgUp...2728293031PgDn
Recommend
@hennes381
Mining Farm Owner
@vcolonramos1989
Individual Miner
@zneedler69
Other Roles
@bberndd
Other Roles
@abdullafareed
Other Roles
@pedrocabelo
Individual Miner
Hot Topics
Lucky Miner LV07 Firmware
6719
As shown in the picture below, T15 machine, 58, 59, 60 are all replaced, it still doesn’t work, what’s the problem.
6533
See the below single-board test result. There are 8.4V,8.5V domain voltage, replacing chip 1 did not work.
6491
How To Install Bitmain S19 And S19j Pro Low Power Mode Firmware: Step-By-Step
5856
Lucky Miner Wi-Fi reconnect
5424
LTC Mining with Lucky Miner Lv06
5306
Back to firmware Lucky Miner Lvl 06: I need the www.bin file. Can someone help?
4869
Lucky miner v6
4828
Cannot access IP address lucky miner
4815
Lucky miner LV06 breakdown
4568
Hot download
Luckyminer LV06-V2.3.0_upgrade firmware 页面升级固件
1415
Luckyminer LV06 factory firmware V2.1.0 页面升级固件
610
Luckyminer Management Tool
582
Solo Miner_Lucky Miner User Guide LV05-LV08_20231215
410
Luckyminer LV07 Instruction and User Guide PC English
176
Luckyminer LV 07 Product Manual
141
SOLO Miner_Nerdminer USB Shape（V3）配置说明1107
136
Luckyminer LV06 ESP-Prog JTAG Debug Guide_Tool kit
135
IceRiver_MinerTool_English_V1.0.15 (1)
127
Luckyminer乐透机用户使用说明LV05-LV08(2023.12.15)
87

No. 199, Zhaojuesi South Rd, Chenghua District, Chengdu, Sichuan, China

No.14, Jian'an Rd, Bao An District, ShenZhen, GuangDong, China

+86 15390421113

minerfixesofficial@gmail.com

About Us Contact Us FAQ News
Privacy Policy Terms & Conditions
2022 Minerfixes - All Rights Reserved